Rle LD1500 Quick Start Bedienungsanleitung PDF herunterladen

Mount the Device

THE LD1500 is a panel mounted device. Use the included wall mount kit and

mount the controller in a convenient location.

Install the Sensing Cable

Leader cable is included with the device and is used to connect sensing cable to

the LD1500, since sensing cable cannot connect directly to the controller.

1. Insert the four stripped wires of the leader cable into the

appropriate slots in the 4-pin terminal block connector -

from left to right: white, black, green, and red. Tighten

the screws on the terminal block connector to secure the

leader cable. Thread the leader cable through a knockout

on the bottom of the enclosure and plug the terminal

block connector into TB2.

2. Unscrew the EOL from the end of the leader cable.

3. Attach the rst length of sensing cable to the leader cable.

4. Route the sensing cable according to your cable layout diagram.

5. Secure the EOL to the unoccupied end of the sensing cable.

Apply Power to the LD1500

A dedicated circuit breaker must be provided within

close proximity to the LD1500 and be clearly marked as

the disconnecting device for the LD1500 leak detection

controller.

RLE recommends using a 24VDC wall adapter power supply (PSWA-DC-24-ST),

which is available separately from RLE.

1. Run a power supply to the location of the unit and plug it into P1. If you’re

trademarks of Raymond & Lae Engineering, Inc. The products sold by Raymond & Lae Engineering, Inc. are subject to the limited warranty, limited

liability, and other terms and conditions of sale set forth at http://rletech.com/RLE-Terms-and-Conditions.html.

Installation Supplies

Included with the LD1500

LD1500 controller

Crossover cable (blue with yellow ends)

15 foot (4.57m) leader cable

End-of-line terminator (EOL)

Available from RLE, Sold Separately

SeaHawk sensing cable - up to 1,500 feet (457m) of conductive uid sensing

cable or 1,050 feet (320m) of chemical sensing cable

Optional Enclosure (LD-ENC)

24VAC power supply (WA-AC-24-ST) or 24VDC power supply (PSWA-DC-24-ST)

Network Communications Information

Consult your IT administrator and determine the following LD1500 network

settings:

• IP Address _______________________________________________

• Subnet Mask _____________________________________________

• Default Gateway __________________________________________

SeaHawk LD1500 Quick Start Guide

Thank you for purchasing a SeaHawk LD1500 distance-read leak detection controller.

This guide outlines basic installation and conguration. Additional support information,

including the LD1500 User Guide, is available on our website - www.rletech.com.

If you need further assistance, please contact RLE Technologies at [email protected]

or call us at 800.518.1519.

v1.0

(05/2013)

1 2

Inhaltsverzeichnis

Seite 1 - Installation Supplies

Mount the DeviceTHE LD1500 is a panel mounted device. Use the included wall mount kit and mount the controller in a convenient location. Install the

Seite 2 - Test the System

wiring power directly, insert the wires into TB1 as noted.2. Apply power. The device will boot. No alarms should be present. If an alarm is presen

Kommentare zu diesen Handbüchern

Keine Kommentare

Rle LD1500 Quick Start Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Rle LD1500 Quick Start herunter. RLE LD1500 Quick Start User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Rle LD1500 Quick Start